mirror of
https://github.com/pbatard/rufus.git
synced 2024-08-14 23:57:05 +00:00
d87f069963
* Adds USB masquerading according to disk ID in USB part table * Adds debug feature * Closes #74 - was due to flags not being properly saved/restored * Closes #71 * Fixes reentrant INT_13h for some platforms (eg. IBM t43p reenters INT_13h to issue an SCSI passthrough, AH=0x50) * Embed MBR as a resource rather than an ms-sys header
58 lines
No EOL
2.9 KiB
Text
58 lines
No EOL
2.9 KiB
Text
Rufus: The Reliable USB Formatting Utility - Custom MBR
|
|
|
|
# Description
|
|
|
|
This directory contains all the resources required to create an MBR that prompts
|
|
the user for boot selection, when a second bootable device (typically bootable
|
|
fixed HDD) is reported by the BIOS at 0x81.
|
|
|
|
This aims at mimicking the Microsoft Windows optical installation media feature,
|
|
which may be necessary on for WinPE 2.x or earlier based installations.
|
|
|
|
This MBR will also masquerade a bootable USB drive booted as 0x80 by the BIOS to
|
|
a different ID according to the one found in its partition table entry. Eg. if
|
|
the partition table lists the disk ID for the first partition as 0x81, then it
|
|
will be swapped for 0x80.
|
|
|
|
# Compilation
|
|
|
|
Any gcc suite (except possibly the X-Code one on OS-X) should be able to compile
|
|
the MBR by invoking 'make'. A 'make dis', that produces a disassembly dump is
|
|
also provided for your convenience.
|
|
|
|
# Primer
|
|
|
|
The way this bootloader achieves the feature highlighted above is as follows:
|
|
1. An attempt to read the MBR of the second bootable drive (0x81) is made
|
|
through INT_13h (in either CHS or LBA mode depending on the extensions
|
|
detected)
|
|
2. If that attempts succeeds, then the partition table from the newly read MBR
|
|
is checked for an active/bootable entry.
|
|
3. If such a partition is found, a prompt is displayed to the user and an RTC
|
|
timer interrupt (INT_8h) override is added so that dots are displayed at
|
|
regular interval. Then the keyboard is checked for entry.
|
|
4. If the user presses a key, the first partition boot record from the USB is
|
|
read (according to the values found in the USB MBR partition table) and
|
|
executed
|
|
5. If no key is pressed, then an INT_13h (disk access interrupt) override is
|
|
added to masquerade the second bootable drive (0x81) as the first one (0x80)
|
|
so that the Windows second stage installer, or any other program relying on
|
|
BIOS disk access, behave as if there was no USB drive inserted.
|
|
6. In case there was a failure to read the second bootable drive's MBR, or no
|
|
active partition was detected there, the USB is booted without prompts.
|
|
7. In case USB is booted, and the drive ID of first partition of the USB (which
|
|
is always assumed bootable) is read and if different from 0x80, then it is
|
|
also swapped with 0x80 in the INT_13h override.
|
|
|
|
# Limitations
|
|
|
|
* If you are using software RAID or a non-conventional setup, the second
|
|
bootable disk may not be accessible through the BIOS and therefore the USB
|
|
will always be booted.
|
|
* Some processes (notably XP's ntdetect.com) do not seem to like gaps in the
|
|
bootable drive sequence, which means that if you set your bootable USB
|
|
partition as 0x82 or higher, and it leaves any of 0x80/0x81 free as a result
|
|
then these processes may report an error.
|
|
* DOS also does not allow anything but 0x80 to be used as bootable disk. Thus
|
|
it is not possible to run MS-DOS or FreeDOS off an USB drive unless the disk
|
|
ID is 0x80 and not masqueraded. |