/* configuration.h - ESP3D configuration file Copyright (c) 2014 Luc Lebosse. All rights reserved. This code is free software; you can redistribute it and/or modify it under the terms of the GNU Lesser General Public License as published by the Free Software Foundation; either version 2.1 of the License, or (at your option) any later version. This code is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU Lesser General Public License for more details. You should have received a copy of the GNU Lesser General Public License along with This code; if not, write to the Free Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA */ #ifndef _CONFIGURATION_H #define _CONFIGURATION_H // ============================================================================ // SD WIFI Pro (FYSETC) configuration // ESP32 / 4MB flash / SDIO 4-bit shared SD // ============================================================================ /* Setup station as default, use AP mode first if not done * Note: need both defined to enable it * Uncomment and edit them to define */ // #define STATION_WIFI_SSID "*********" // #define STATION_WIFI_PASSWORD "*********" /* You can also use a different config file for SSID/password * Just save it in same location as this configuration.h * This file is ignored by github */ #if defined __has_include #if __has_include("myconfig.h") #include "myconfig.h" #endif #endif /************************************ * * Serial Communications * * Settings and protocols * ************************************/ /* Serial Communication protocol * RAW_SERIAL // Basic serial protocol, without data change * MKS_SERIAL // MakerBase communication protocol */ #define COMMUNICATION_PROTOCOL RAW_SERIAL /* Main Serial port * USE_SERIAL_0 / USE_SERIAL_1 / USE_SERIAL_2 */ #define ESP_SERIAL_OUTPUT USE_SERIAL_0 /* Serial buffer size * Maximum size of the serial buffer */ #define SERIAL_RX_BUFFER_SIZE 512 /************************************ * * Target firmware * * Not used - this is a standalone SD WiFi device * ************************************/ #define DEFAULT_FW UNKNOWN_FW /************************************ * * Radio mode of ESP3D * * The radio mode ESP3D communicate with the network * ************************************/ /* Use WiFi * Enable wifi communications */ #define WIFI_FEATURE /************************************ * * Channels of ESP3D * * The way ESP3D communicate * ************************************/ /* Use Web server * Enable http server */ #define HTTP_FEATURE /* Use Websocket server * Enable websocket communications */ #define WS_DATA_FEATURE // Enable notifications // Allows to send notifications to the user #define NOTIFICATION_FEATURE /* Notification message when online * The message that will be sent when the ESP is online */ #define NOTIFICATION_ESP_ONLINE "Hi, %ESP_NAME% is now online at %ESP_IP%" /* Notification title message * The title of notification */ #define ESP_NOTIFICATION_TITLE "SD WIFI Pro Notification" /************************************ * * Discovery methods of ESP3D * * The discovery methods of ESP3D * ************************************/ /* Use captive portal * Enable captive portal in AP mode */ #define CAPTIVE_PORTAL_FEATURE /* Use mDNS discovery * This method need `bonjour` protocol on windows, or `avahi` on linux */ #define MDNS_FEATURE /* Use Simple Service Discovery Protocol * It is supported on Windows out of the box */ #define SSDP_FEATURE /************************************ * * SSDP Customization settings * * Customize your ESP3D * ************************************/ /* Model name */ #define ESP_MODEL_NAME "SD_WIFI_PRO" /* Model number */ #define ESP_MODEL_NUMBER "SWP 1.0" /* Model url */ #define ESP_MODEL_URL "https://github.com/FYSETC/SD-WIFI-PRO" /* Manufacturer name */ #define ESP_MANUFACTURER_NAME "FYSETC" /* Manufacturer url */ #define ESP_MANUFACTURER_URL "https://www.fysetc.com" /************************************ * * Flash filesystem * * Filesystem on flash * ************************************/ /* File system type used by ESP3D * ESP_SPIFFS_FILESYSTEM (Deprecated) * ESP_FAT_FILESYSTEM (ESP32 only with large partitions) * ESP_LITTLEFS_FILESYSTEM (Default) */ #define FILESYSTEM_FEATURE ESP_LITTLEFS_FILESYSTEM /* Enable date/time on files * Set date/time on files using SNTP or last webui connection */ #define FILESYSTEM_TIMESTAMP_FEATURE /************************************ * * SD filesystem * * Filesystem on SD card - SDIO 4-bit shared mode * ************************************/ /* SD card connection * ESP_SHARED_SD: both host and ESP share the SD card */ #define SD_DEVICE_CONNECTION ESP_SHARED_SD /* SD card library * ESP_SDIO: ESP32 SDMMC (4-bit mode) */ #define SD_DEVICE ESP_SDIO /* SDIO bit mode * SD_FOUR_BIT_MODE for maximum throughput */ #define SDIO_BIT_MODE SD_FOUR_BIT_MODE /* Enable date/time on files */ #define SD_TIMESTAMP_FEATURE /************************************ * * SD card pins (SDIO mode for SD WIFI Pro) * ************************************/ /* SD shared flag pin * Active LOW to claim SD for ESP */ #define ESP_FLAG_SHARED_SD_PIN 26 #define ESP_FLAG_SHARED_SD_VALUE 0 /* SDIO pins (standard ESP32 SDMMC pins) */ #define ESP_SDIO_CLK_PIN 14 #define ESP_SDIO_CMD_PIN 15 #define ESP_SDIO_D0_PIN 2 #define ESP_SDIO_D1_PIN 4 #define ESP_SDIO_D2_PIN 12 #define ESP_SDIO_D3_PIN 13 /************************************ * * Remote access * * Remote filesystem access * ************************************/ /* Enable global filesystem * Allows to access to all filesystems from same location */ #define GLOBAL_FILESYSTEM_FEATURE /* WebDav access * FS_ROOT / FS_FLASH / FS_SD */ #define WEBDAV_FEATURE FS_SD /* FTP access (1 connection only) * FS_ROOT / FS_FLASH / FS_SD */ #define FTP_FEATURE FS_SD /************************************ * * Update ESP3D * * Update ESP3D firmware * ************************************/ /* Enable Web Update * Update firmware using WebUI, need 4MB of flash */ #define WEB_UPDATE_FEATURE /* Disable serial forwarding to external device * No printer/CNC connected - this is a standalone SD WiFi device. * Non-ESP commands are dropped instead of forwarded to serial. */ #define NO_SERIAL_FORWARD /* Settings location * SETTINGS_IN_EEPROM //ESP8266/ESP32 * SETTINGS_IN_PREFERENCES //ESP32 only */ #define ESP_SAVE_SETTINGS SETTINGS_IN_EEPROM /************************************ * * Development setting * Do not modify them for production ************************************/ // Enable log mode // LOG_OUTPUT_SERIAL0 / LOG_OUTPUT_SERIAL1 / LOG_OUTPUT_SERIAL2 // LOG_OUTPUT_TELNET / LOG_OUTPUT_WEBSOCKET // #define ESP_LOG_FEATURE LOG_OUTPUT_SERIAL0 // #define ESP3D_LOG_LEVEL LOG_LEVEL_DEBUG #ifdef ESP_LOG_FEATURE #define LOG_ESP3D_BAUDRATE 115200 #define LOG_ESP3D_OUTPUT_PORT 8000 #endif // ESP_LOG_FEATURE // Enable benchmark report in dev console // #define ESP_BENCHMARK_FEATURE // Disable sanity check at compilation // #define ESP_NO_SANITY_CHECK /************************************ * * Sanity checks * Do not modify ************************************/ #if defined(ESP_GOT_DATE_TIME_HOOK) || defined(SD_TIMESTAMP_FEATURE) || \ defined(FILESYSTEM_TIMESTAMP_FEATURE) #define TIMESTAMP_FEATURE #endif // SD_TIMESTAMP_FEATURE || FILESYSTEM_TIMESTAMP_FEATURE #if defined(CAMERA_DEVICE) #if CAMERA_DEVICE == CAMERA_MODEL_ESP32_CAM_BOARD || \ CAMERA_DEVICE == CAMERA_MODEL_ESP32S2_CAM_BOARD #define USE_BOARD_HEARDER 1 #endif #endif // CAMERA_DEVICE #if !defined(WIFI_FEATURE) && !defined(ETH_FEATURE) #undef HTTP_FEATURE #undef TELNET_FEATURE #undef WEBDAV_FEATURE #undef FTP_FEATURE #undef WEB_UPDATE_FEATURE #undef CAPTIVE_PORTAL_FEATURE #undef SSDP_FEATURE #undef MDNS_FEATURE #undef NOTIFICATION_FEATURE #endif #endif //_CONFIGURATION_H