diff --git a/arduino_maze/motorControl.ino b/arduino_maze/motorControl.ino
deleted file mode 100644
index 5b88d83..0000000
--- a/arduino_maze/motorControl.ino
+++ /dev/null
@@ -1,120 +0,0 @@
-// 3.6 2 amps
-
-
-const int rangeSTick = 1023; // 0 is bottom
-const int reangle = 45, angleRange = 90; // 0 is bottom
-const float transformDesireToAngle = .09; // tranpoe
-const int stillJoystick = 511;
-const int deadband = 10;
-const int motorPulseDelay = 500;
-
-const float angleChange = 1.8;
-float x = 0, y = 0; //angle of current postion
- 
-class MotorControl
-{
-  public:
-  float currentPostion;
-  float goPostion;
-  int pastDesire = stillJoystick;
-  bool reset;
-  bool isButtonPressed;
-  int whichButton;
-  int dire, puls;
-  
-    MotorControl(int dire, int puls)
-    {
-      pinMode(dire,OUTPUT);
-      pinMode(puls,OUTPUT);
-      direct = dire;
-      pulse = puls;
-      yIsNo = isX;
-      currentPostion = reangle;
-    }
-    void whatToDo(int desire)
-    {
-      if (desire < 0)
-      button = desire * -1;
-      else
-      goto yeet;
-      switch (button)
-      {
-        case default:
-        goto yeet;
-        case 1:
-goto caseEnd;
-        case 2:
-goto caseEnd;
-        case 3:
-goto caseEnd;
-        case 4:
-goto caseEnd;
-        case 5:
-goto caseEnd;
-        case 6:
-goto caseEnd;
-        case 7: 
-      caseEnd:  
-      button = 0;
-      goto skip; 
-      }
-      yeet:
-      if(desire > (pastDesire + 10) || desire < (pastDesire - 10)) // noise from constant stick upload
-      {
-        goPostion = tranpose();
-        pastdesire = desire;
-      }
-
-      // two pins
-      if(goPostion > (currentpostion + 5.0))
-      {
-        digitalWrite(direct, HIGH);
-        currentpostion += angleChange;
-        digitalWrite(pulse,HIGH); 
-        delayMicroseconds(motorPulseDelay); 
-        digitalWrite(pulse,LOW); 
-        delayMicroseconds(motorPulseDelay);
-      }
-      break;
-      if((currentpostion - 5.0) > goPostion)
-      {
-        digitalWrite(direct, LOW);
-        currentpostion -= angleChange;
-        digitalWrite(pulse,HIGH); 
-        delayMicroseconds(motorPulseDelay); 
-        digitalWrite(pulse,LOW); 
-        delayMicroseconds(motorPulseDelay);
-      }
-    }
-    float tranpose()
-    {
-      int temp = desire * transformDesireToAngle;
-      return temp;
-    }
-    void calibrate()
-    {
-      currentpostion = reangle;
-      goPostion = reangle
-    }
-}
-
-
-// defines pins numbers
-const int stepPinM1 = 3; // motor 1
-const int dirPinM1 = 5;
-const int stepPinM2  = 6; // motor 2
-const int dirPinM2 = 9;
-
-MotorControl xMotor(stepPinM1, dirPinM1)
-MotorControl yMotor(stepPinM2, dirPinM2)
-
-void setup() {
-  
-}
-
-
-void loop() {
-  xMotor.whatToDo();// angle
-  yMotor.whatToDo();// angle
-  skip:
-}