This curbs runaway growth while still allowing substantial
spikes in block weight
Original specification from ArticMine:
here is the scaling proposal
Define: LongTermBlockWeight
Before fork:
LongTermBlockWeight = BlockWeight
At or after fork:
LongTermBlockWeight = min(BlockWeight, 1.4*LongTermEffectiveMedianBlockWeight)
Note: To avoid possible consensus issues over rounding the LongTermBlockWeight for a given block should be calculated to the nearest byte, and stored as a integer in the block itself. The stored LongTermBlockWeight is then used for future calculations of the LongTermEffectiveMedianBlockWeight and not recalculated each time.
Define: LongTermEffectiveMedianBlockWeight
LongTermEffectiveMedianBlockWeight = max(300000, MedianOverPrevious100000Blocks(LongTermBlockWeight))
Change Definition of EffectiveMedianBlockWeight
From (current definition)
EffectiveMedianBlockWeight = max(300000, MedianOverPrevious100Blocks(BlockWeight))
To (proposed definition)
EffectiveMedianBlockWeight = min(max(300000, MedianOverPrevious100Blocks(BlockWeight)), 50*LongTermEffectiveMedianBlockWeight)
Notes:
1) There are no other changes to the existing penalty formula, median calculation, fees etc.
2) There is the requirement to store the LongTermBlockWeight of a block unencrypted in the block itself. This is to avoid possible consensus issues over rounding and also to prevent the calculations from becoming unwieldy as we move away from the fork.
3) When the EffectiveMedianBlockWeight cap is reached it is still possible to mine blocks up to 2x the EffectiveMedianBlockWeight by paying the corresponding penalty.
Note: the long term block weight is stored in the database, but not in the actual block itself,
since it requires recalculating anyway for verification.
The blockchain prunes seven eighths of prunable tx data.
This saves about two thirds of the blockchain size, while
keeping the node useful as a sync source for an eighth
of the blockchain.
No other data is currently pruned.
There are three ways to prune a blockchain:
- run monerod with --prune-blockchain
- run "prune_blockchain" in the monerod console
- run the monero-blockchain-prune utility
The first two will prune in place. Due to how LMDB works, this
will not reduce the blockchain size on disk. Instead, it will
mark parts of the file as free, so that future data will use
that free space, causing the file to not grow until free space
grows scarce.
The third way will create a second database, a pruned copy of
the original one. Since this is a new file, this one will be
smaller than the original one.
Once the database is pruned, it will stay pruned as it syncs.
That is, there is no need to use --prune-blockchain again, etc.
get_output_key method is commonly used when working with txs and their key images. Because the method is not const, passing blockchain object though const& or pointers to const is not possible in this context. This is especially problematic in external projects (e.g., projects in moneroexamples) that use monero C++ api to operate on the blockchain and txs.
Thus, having get_output_key method will simplify moving blockchain object around through const references and pointers to const objects.
a48f2dab blockchain_prune_known_spent_data: blackball file is now optional (moneromooo-monero)
17b45725 Outputs where all amounts are known spent can now be pruned (moneromooo-monero)
Only for pre rct for obvious reasons.
Note: DO NOT use a known spent list which includes outputs
which are not known spent. If the list includes any output
that's just strongly thought to be spent, but not provably
so, you risk finding yourself unable to sync past the point
where that output is spent.
I estimate only 200 MB saved on current mainnet though,
unless the new blackballing rule unearths a good amount of
large-amount-set extra spent outs.
149da42 db_lmdb: enable batch transactions by default (stoffu)
34cb6b4 add --regtest and --fixed-difficulty for regression testing (vicsn)
9e1403e update get_info RPC and bump RPC version (vicsn)
207b66e first new functional tests (vicsn)
This gets rid of the temporary precalc cache.
Also make the RPC able to send data back in binary or JSON,
since there can be a lot of data
This bumps the LMDB database format to v3, with migration.
on_generateblocks RPC call combines functionality from the on_getblocktemplate and on_submitblock RPC calls to allow rapid block creation. Difficulty is set permanently to 1 for regtest.
Makes use of FAKECHAIN network type, but takes hard fork heights from mainchain
Default reserve_size in generate_blocks RPC call is now 1. If it is 0, the following error occurs 'Failed to calculate offset for'.
Queries hard fork heights info of other network types
This patch allows to filter out sensitive information for queries that rely on the pool state, when running in restricted mode.
This filtering is only applied to data sent back to RPC queries. Results of inline commands typed locally in the daemon are not affected.
In practice, when running with `--restricted-rpc`:
* get_transaction_pool will list relayed transactions with the fields "last relayed time" and "received time" set to zero.
* get_transaction_pool will not list transaction that have do_not_relay set to true, and will not list key images that are used only for such transactions
* get_transaction_pool_hashes.bin will not list such transaction
* get_transaction_pool_stats will not count such transactions in any of the aggregated values that are computed
The implementation does not make filtering the default, so developers should be mindful of this if they add new RPC functionality.
Fixes#2590.
Transactions in the txpool are marked when another transaction
is seen double spending one or more of its inputs.
This is then exposed wherever appropriate.
Note that being marked with this "double spend seen" flag does
NOT mean this transaction IS a double spend and will never be
mined: it just means that the network has seen at least another
transaction spending at least one of the same inputs, so care
should be taken to wait for a few confirmations before acting
upon that transaction (ie, mostly of use for merchants wanting
to accept unconfirmed transactions).
And optimize import startup:
Remember start_height position during initial count_blocks pass
to avoid having to reread entire file again to arrive at start_height
If monerod is started with default sync mode, set it to SAFE after
synchronization completes. Set it back to FAST if synchronization
restarts (e.g. because another peer has a longer blockchain).
If monerod is started with an explicit sync mode, none of this
automation takes effect.
