506 lines
17 KiB
Text
506 lines
17 KiB
Text
# ------------------------------------------------------------------------------
|
|
# /etc/tlp.conf - TLP user configuration (version 1.4)
|
|
# See full explanation: https://linrunner.de/tlp/settings
|
|
#
|
|
# Settings are read in the following order:
|
|
#
|
|
# 1. Intrinsic defaults
|
|
# 2. /etc/tlp.d/*.conf - Drop-in customization snippets
|
|
# 3. /etc/tlp.conf - User configuration (this file)
|
|
#
|
|
# Notes:
|
|
# - In case of identical parameters, the last occurence has precedence
|
|
# - This also means, parameters enabled here will override anything else
|
|
# - However you may append values to a parameter already defined as intrinsic
|
|
# default or in a previously read file: use PARAMETER+="add values"
|
|
# - IMPORTANT: all parameters here are disabled; remove the leading '#' if you
|
|
# like to enable a feature without default or have a value different from the
|
|
# default
|
|
# - Default *: intrinsic default that is effective when the parameter is missing
|
|
# or disabled by a leading '#'; use PARAM="" to disable an intrinsic default
|
|
# - Default <none>: do nothing or use kernel/hardware defaults
|
|
# -
|
|
# ------------------------------------------------------------------------------
|
|
# tlp - Parameters for power saving
|
|
|
|
# Set to 0 to disable, 1 to enable TLP.
|
|
TLP_ENABLE=1
|
|
|
|
# Control how warnings about invalid settings are issued:
|
|
# 0=disabled,
|
|
# 1=background tasks (boot, resume, change of power source) report to syslog,
|
|
# 2=shell commands report to the terminal (stderr),
|
|
# 3=combination of 1 and 2
|
|
# Default: 3
|
|
|
|
#TLP_WARN_LEVEL=3
|
|
|
|
# Operation mode when no power supply can be detected: AC, BAT.
|
|
# Concerns some desktop and embedded hardware only.
|
|
TLP_DEFAULT_MODE=AC
|
|
|
|
# Operation mode select: 0=depend on power source, 1=always use TLP_DEFAULT_MODE
|
|
# Note: use in conjunction with TLP_DEFAULT_MODE=BAT for BAT settings on AC.
|
|
TLP_PERSISTENT_DEFAULT=0
|
|
|
|
# Power supply classes to ignore when determining operation mode: AC, USB, BAT.
|
|
# Separate multiple classes with spaces.
|
|
# Note: try on laptops where operation mode AC/BAT is incorrectly detected.
|
|
# Default: <none>
|
|
|
|
#TLP_PS_IGNORE="BAT"
|
|
|
|
# Seconds laptop mode has to wait after the disk goes idle before doing a sync.
|
|
# Non-zero value enables, zero disables laptop mode.
|
|
DISK_IDLE_SECS_ON_AC=0
|
|
DISK_IDLE_SECS_ON_BAT=2
|
|
|
|
# Dirty page values (timeouts in secs).
|
|
# Default: 15 (AC), 60 (BAT)
|
|
|
|
#MAX_LOST_WORK_SECS_ON_AC=15
|
|
#MAX_LOST_WORK_SECS_ON_BAT=60
|
|
|
|
# Select a CPU frequency scaling governor.
|
|
# Intel processor with intel_pstate driver:
|
|
# performance, powersave(*).
|
|
# Intel processor with intel_cpufreq driver (aka intel_pstate passive mode):
|
|
# conservative, ondemand, userspace, powersave, performance, schedutil(*).
|
|
# Intel and other processor brands with acpi-cpufreq driver:
|
|
# conservative, ondemand(*), userspace, powersave, performance, schedutil(*).
|
|
# Use tlp-stat -p to show the active driver and available governors.
|
|
# Important:
|
|
# Governors marked (*) above are power efficient for *almost all* workloads
|
|
# and therefore kernel and most distributions have chosen them as defaults.
|
|
# You should have done your research about advantages/disadvantages *before*
|
|
# changing the governor.
|
|
CPU_SCALING_GOVERNOR_ON_AC=performance
|
|
CPU_SCALING_GOVERNOR_ON_BAT=powersave
|
|
|
|
# Set the min/max frequency available for the scaling governor.
|
|
# Possible values depend on your CPU. For available frequencies see
|
|
# the output of tlp-stat -p.
|
|
# Notes:
|
|
# - Min/max frequencies must always be specified for both AC *and* BAT
|
|
# - Not recommended for use with the intel_pstate scaling driver, use
|
|
# CPU_MIN/MAX_PERF_ON_AC/BAT below instead
|
|
# Default: <none>
|
|
|
|
#CPU_SCALING_MIN_FREQ_ON_AC=0
|
|
#CPU_SCALING_MAX_FREQ_ON_AC=0
|
|
#CPU_SCALING_MIN_FREQ_ON_BAT=0
|
|
#CPU_SCALING_MAX_FREQ_ON_BAT=0
|
|
|
|
# Set Intel CPU energy/performance policies HWP.EPP and EPB:
|
|
# performance, balance_performance, default, balance_power, power.
|
|
# Values are given in order of increasing power saving.
|
|
# Notes:
|
|
# - HWP.EPP: requires kernel 4.10, intel_pstate scaling driver and Intel Core i
|
|
# 6th gen. or newer CPU
|
|
# - EPB: requires kernel 5.2 or module msr and x86_energy_perf_policy from
|
|
# linux-tools, intel_pstate or intel_cpufreq scaling driver and Intel Core i
|
|
# 2nd gen. or newer CPU
|
|
# - When HWP.EPP is available, EPB is not set
|
|
# Default: balance_performance (AC), balance_power (BAT)
|
|
|
|
#CPU_ENERGY_PERF_POLICY_ON_AC=balance_performance
|
|
#CPU_ENERGY_PERF_POLICY_ON_BAT=balance_power
|
|
|
|
# Set Intel CPU P-state performance: 0..100 (%).
|
|
# Limit the max/min P-state to control the power dissipation of the CPU.
|
|
# Values are stated as a percentage of the available performance.
|
|
# Requires intel_pstate or intel_cpufreq driver and Intel Core i 2nd gen. or
|
|
# newer CPU.
|
|
# Default: <none>
|
|
|
|
#CPU_MIN_PERF_ON_AC=0
|
|
#CPU_MAX_PERF_ON_AC=100
|
|
#CPU_MIN_PERF_ON_BAT=0
|
|
#CPU_MAX_PERF_ON_BAT=30
|
|
|
|
# Set the CPU "turbo boost" (Intel) or "turbo core" (AMD) feature:
|
|
# 0=disable, 1=allow.
|
|
# Note: a value of 1 does *not* activate boosting, it just allows it.
|
|
CPU_BOOST_ON_AC=1
|
|
CPU_BOOST_ON_BAT=0
|
|
|
|
# Set the Intel CPU HWP dynamic boost feature:
|
|
# 0=disable, 1=enable.
|
|
# Requires intel_pstate scaling driver in 'active' mode and Intel Core i
|
|
# 6th gen. or newer CPU.
|
|
CPU_HWP_DYN_BOOST_ON_AC=1
|
|
CPU_HWP_DYN_BOOST_ON_BAT=0
|
|
|
|
# Minimize number of used CPU cores/hyper-threads under light load conditions:
|
|
# 0=disable, 1=enable.
|
|
SCHED_POWERSAVE_ON_AC=0
|
|
SCHED_POWERSAVE_ON_BAT=1
|
|
|
|
# Kernel NMI Watchdog:
|
|
# 0=disable (default, saves power), 1=enable (for kernel debugging only).
|
|
# Default: 0
|
|
|
|
#NMI_WATCHDOG=0
|
|
|
|
# Select platform profile:
|
|
# performance, balanced, low-power.
|
|
# Controls system operating characteristics around power/performance levels,
|
|
# thermal and fan speed. Values are given in order of increasing power saving.
|
|
# Note: check the output of tlp-stat -p to determine availability on your
|
|
# hardware and additional profiles such as: balanced-performance, quiet, cool.
|
|
PLATFORM_PROFILE_ON_AC=balanced_performance
|
|
PLATFORM_PROFILE_ON_BAT=balance_power
|
|
|
|
# Define disk devices on which the following DISK/AHCI_RUNTIME parameters act.
|
|
# Separate multiple devices with spaces.
|
|
# Devices can be specified by disk ID also (lookup with: tlp diskid).
|
|
# Default: "nvme0n1 sda"
|
|
|
|
#DISK_DEVICES="nvme0n1 sda"
|
|
|
|
# Disk advanced power management level: 1..254, 255 (max saving, min, off).
|
|
# Levels 1..127 may spin down the disk; 255 allowable on most drives.
|
|
# Separate values for multiple disks with spaces. Use the special value 'keep'
|
|
# to keep the hardware default for the particular disk.
|
|
# Default: 254 (AC), 128 (BAT)
|
|
|
|
#DISK_APM_LEVEL_ON_AC="254 254"
|
|
#DISK_APM_LEVEL_ON_BAT="128 128"
|
|
|
|
# Exclude disk classes from advanced power management (APM):
|
|
# sata, ata, usb, ieee1394.
|
|
# Separate multiple classes with spaces.
|
|
# CAUTION: USB and IEEE1394 disks may fail to mount or data may get corrupted
|
|
# with APM enabled. Be careful and make sure you have backups of all affected
|
|
# media before removing 'usb' or 'ieee1394' from the denylist!
|
|
# Default: "usb ieee1394"
|
|
|
|
#DISK_APM_CLASS_DENYLIST="usb ieee1394"
|
|
|
|
# Hard disk spin down timeout:
|
|
# 0: spin down disabled
|
|
# 1..240: timeouts from 5s to 20min (in units of 5s)
|
|
# 241..251: timeouts from 30min to 5.5 hours (in units of 30min)
|
|
# See 'man hdparm' for details.
|
|
# Separate values for multiple disks with spaces. Use the special value 'keep'
|
|
# to keep the hardware default for the particular disk.
|
|
DISK_SPINDOWN_TIMEOUT_ON_AC="keep"
|
|
DISK_SPINDOWN_TIMEOUT_ON_BAT="keep"
|
|
|
|
# Select I/O scheduler for the disk devices.
|
|
# Multi queue (blk-mq) schedulers:
|
|
# mq-deadline(*), none, kyber, bfq
|
|
# Single queue schedulers:
|
|
# deadline(*), cfq, bfq, noop
|
|
# (*) recommended.
|
|
# Separate values for multiple disks with spaces. Use the special value 'keep'
|
|
# to keep the kernel default scheduler for the particular disk.
|
|
# Notes:
|
|
# - Multi queue (blk-mq) may need kernel boot option 'scsi_mod.use_blk_mq=1'
|
|
# and 'modprobe mq-deadline-iosched|kyber|bfq' on kernels < 5.0
|
|
# - Single queue schedulers are legacy now and were removed together with
|
|
# the old block layer in kernel 5.0
|
|
# Default: keep
|
|
|
|
#DISK_IOSCHED="mq-deadline mq-deadline"
|
|
|
|
# AHCI link power management (ALPM) for SATA disks:
|
|
# min_power, med_power_with_dipm(*), medium_power, max_performance.
|
|
# (*) Kernel 4.15 (or newer) required, then recommended.
|
|
# Multiple values separated with spaces are tried sequentially until success.
|
|
# Default:
|
|
# - "med_power_with_dipm max_performance" (AC)
|
|
# - "med_power_with_dipm min_power" (BAT)
|
|
|
|
#SATA_LINKPWR_ON_AC="med_power_with_dipm max_performance"
|
|
#SATA_LINKPWR_ON_BAT="med_power_with_dipm min_power"
|
|
|
|
# Exclude SATA links from AHCI link power management (ALPM).
|
|
# SATA links are specified by their host. Refer to the output of
|
|
# tlp-stat -d to determine the host; the format is "hostX".
|
|
# Separate multiple hosts with spaces.
|
|
# Default: <none>
|
|
|
|
#SATA_LINKPWR_DENYLIST="host1"
|
|
|
|
# Runtime Power Management for NVMe, SATA, ATA and USB disks
|
|
# as well as SATA ports:
|
|
# on=disable, auto=enable.
|
|
# Note: SATA controllers are PCIe bus devices and handled by RUNTIME_PM further
|
|
# down.
|
|
|
|
# Default: on (AC), auto (BAT)
|
|
|
|
#AHCI_RUNTIME_PM_ON_AC=on
|
|
#AHCI_RUNTIME_PM_ON_BAT=auto
|
|
|
|
# Seconds of inactivity before disk is suspended.
|
|
# Note: effective only when AHCI_RUNTIME_PM_ON_AC/BAT is activated.
|
|
# Default: 15
|
|
|
|
#AHCI_RUNTIME_PM_TIMEOUT=15
|
|
|
|
# Power off optical drive in UltraBay/MediaBay: 0=disable, 1=enable.
|
|
# Drive can be powered on again by releasing (and reinserting) the eject lever
|
|
# or by pressing the disc eject button on newer models.
|
|
# Note: an UltraBay/MediaBay hard disk is never powered off.
|
|
# Default: 0
|
|
|
|
#BAY_POWEROFF_ON_AC=0
|
|
#BAY_POWEROFF_ON_BAT=0
|
|
|
|
# Optical drive device to power off
|
|
# Default: sr0
|
|
|
|
#BAY_DEVICE="sr0"
|
|
|
|
# Set the min/max/turbo frequency for the Intel GPU.
|
|
# Possible values depend on your hardware. For available frequencies see
|
|
# the output of tlp-stat -g.
|
|
# Default: <none>
|
|
|
|
#INTEL_GPU_MIN_FREQ_ON_AC=0
|
|
#INTEL_GPU_MIN_FREQ_ON_BAT=0
|
|
#INTEL_GPU_MAX_FREQ_ON_AC=0
|
|
#INTEL_GPU_MAX_FREQ_ON_BAT=0
|
|
#INTEL_GPU_BOOST_FREQ_ON_AC=0
|
|
#INTEL_GPU_BOOST_FREQ_ON_BAT=0
|
|
|
|
# AMD GPU power management.
|
|
# Performance level (DPM): auto, low, high; auto is recommended.
|
|
# Note: requires amdgpu or radeon driver.
|
|
# Default: auto
|
|
|
|
#RADEON_DPM_PERF_LEVEL_ON_AC=auto
|
|
#RADEON_DPM_PERF_LEVEL_ON_BAT=auto
|
|
|
|
# Dynamic power management method (DPM): balanced, battery, performance.
|
|
# Note: radeon driver only.
|
|
# Default: <none>
|
|
|
|
#RADEON_DPM_STATE_ON_AC=performance
|
|
#RADEON_DPM_STATE_ON_BAT=battery
|
|
|
|
# Graphics clock speed (profile method): low, mid, high, auto, default;
|
|
# auto = mid on BAT, high on AC.
|
|
# Note: radeon driver on legacy ATI hardware only (where DPM is not available).
|
|
# Default: default
|
|
|
|
#RADEON_POWER_PROFILE_ON_AC=default
|
|
#RADEON_POWER_PROFILE_ON_BAT=default
|
|
|
|
# Wi-Fi power saving mode: on=enable, off=disable.
|
|
WIFI_PWR_ON_AC=off
|
|
WIFI_PWR_ON_BAT=off
|
|
|
|
# Disable Wake-on-LAN: Y/N.
|
|
# Default: Y
|
|
|
|
#WOL_DISABLE=Y
|
|
|
|
# Enable audio power saving for Intel HDA, AC97 devices (timeout in secs).
|
|
# A value of 0 disables, >= 1 enables power saving.
|
|
# Note: 1 is recommended for Linux desktop environments with PulseAudio,
|
|
# systems without PulseAudio may require 10.
|
|
SOUND_POWER_SAVE_ON_AC=0
|
|
SOUND_POWER_SAVE_ON_BAT=10
|
|
|
|
# Disable controller too (HDA only): Y/N.
|
|
# Note: effective only when SOUND_POWER_SAVE_ON_AC/BAT is activated.
|
|
# Default: Y
|
|
|
|
#SOUND_POWER_SAVE_CONTROLLER=Y
|
|
|
|
# PCIe Active State Power Management (ASPM):
|
|
# default(*), performance, powersave, powersupersave.
|
|
# (*) keeps BIOS ASPM defaults (recommended)
|
|
# Default: <none>
|
|
|
|
#PCIE_ASPM_ON_AC=default
|
|
#PCIE_ASPM_ON_BAT=default
|
|
|
|
# Runtime Power Management for PCIe bus devices: on=disable, auto=enable.
|
|
# Default: on (AC), auto (BAT)
|
|
|
|
#RUNTIME_PM_ON_AC=on
|
|
#RUNTIME_PM_ON_BAT=auto
|
|
|
|
# Exclude listed PCIe device adresses from Runtime PM.
|
|
# Note: this preserves the kernel driver default, to force a certain state
|
|
# use RUNTIME_PM_ENABLE/DISABLE instead.
|
|
# Separate multiple addresses with spaces.
|
|
# Use lspci to get the adresses (1st column).
|
|
# Default: <none>
|
|
|
|
#RUNTIME_PM_DENYLIST="11:22.3 44:55.6"
|
|
|
|
# Exclude PCIe devices assigned to the listed drivers from Runtime PM.
|
|
# Note: this preserves the kernel driver default, to force a certain state
|
|
# use RUNTIME_PM_ENABLE/DISABLE instead.
|
|
# Separate multiple drivers with spaces.
|
|
# Default: "mei_me nouveau radeon", use "" to disable completely.
|
|
|
|
#RUNTIME_PM_DRIVER_DENYLIST="mei_me nouveau radeon"
|
|
|
|
# Permanently enable/disable Runtime PM for listed PCIe device addresses
|
|
# (independent of the power source). This has priority over all preceding
|
|
# Runtime PM settings. Separate multiple addresses with spaces.
|
|
# Use lspci to get the adresses (1st column).
|
|
# Default: <none>
|
|
|
|
#RUNTIME_PM_ENABLE="11:22.3"
|
|
#RUNTIME_PM_DISABLE="44:55.6"
|
|
|
|
# Set to 0 to disable, 1 to enable USB autosuspend feature.
|
|
USB_AUTOSUSPEND=1
|
|
|
|
# Exclude listed devices from USB autosuspend (separate with spaces).
|
|
# Use lsusb to get the ids.
|
|
# Note: input devices (usbhid) and libsane-supported scanners are excluded
|
|
# automatically.
|
|
# Default: <none>
|
|
|
|
#USB_DENYLIST="1111:2222 3333:4444"
|
|
|
|
# Exclude audio devices from USB autosuspend:
|
|
# 0=do not exclude, 1=exclude.
|
|
USB_EXCLUDE_AUDIO=1
|
|
|
|
# Exclude bluetooth devices from USB autosuspend:
|
|
# 0=do not exclude, 1=exclude.
|
|
# Default: 0
|
|
|
|
#USB_EXCLUDE_BTUSB=0
|
|
|
|
# Exclude phone devices from USB autosuspend:
|
|
# 0=do not exclude, 1=exclude (enable charging).
|
|
USB_EXCLUDE_PHONE=0
|
|
|
|
# Exclude printers from USB autosuspend:
|
|
# 0=do not exclude, 1=exclude.
|
|
# Default: 1
|
|
|
|
#USB_EXCLUDE_PRINTER=1
|
|
|
|
# Exclude WWAN devices from USB autosuspend:
|
|
# 0=do not exclude, 1=exclude.
|
|
# Default: 0
|
|
|
|
#USB_EXCLUDE_WWAN=0
|
|
|
|
# Allow USB autosuspend for listed devices even if already denylisted or
|
|
# excluded above (separate with spaces). Use lsusb to get the ids.
|
|
# Default: 0
|
|
|
|
#USB_ALLOWLIST="1111:2222 3333:4444"
|
|
|
|
# Set to 1 to disable autosuspend before shutdown, 0 to do nothing
|
|
# Note: use as a workaround for USB devices that cause shutdown problems.
|
|
USB_AUTOSUSPEND_DISABLE_ON_SHUTDOWN=0
|
|
|
|
# Restore radio device state (Bluetooth, WiFi, WWAN) from previous shutdown
|
|
# on system startup: 0=disable, 1=enable.
|
|
# Note: the parameters DEVICES_TO_DISABLE/ENABLE_ON_STARTUP/SHUTDOWN below
|
|
# are ignored when this is enabled.
|
|
# Default: 0
|
|
|
|
#RESTORE_DEVICE_STATE_ON_STARTUP=0
|
|
|
|
# Radio devices to disable on startup: bluetooth, nfc, wifi, wwan.
|
|
# Separate multiple devices with spaces.
|
|
DEVICES_TO_DISABLE_ON_STARTUP="bluetooth"
|
|
|
|
# Radio devices to enable on startup: bluetooth, nfc, wifi, wwan.
|
|
# Separate multiple devices with spaces.
|
|
DEVICES_TO_ENABLE_ON_STARTUP="wifi wwan"
|
|
|
|
# Radio devices to disable on shutdown: bluetooth, nfc, wifi, wwan.
|
|
# Note: use as a workaround for devices that are blocking shutdown.
|
|
DEVICES_TO_DISABLE_ON_SHUTDOWN="bluetooth nfc wifi wwan"
|
|
|
|
# Radio devices to enable on shutdown: bluetooth, nfc, wifi, wwan.
|
|
# (to prevent other operating systems from missing radios).
|
|
# Default: <none>
|
|
|
|
#DEVICES_TO_ENABLE_ON_SHUTDOWN="wwan"
|
|
|
|
# Radio devices to enable on AC: bluetooth, nfc, wifi, wwan.
|
|
# Default: <none>
|
|
|
|
#DEVICES_TO_ENABLE_ON_AC="bluetooth nfc wifi wwan"
|
|
|
|
# Radio devices to disable on battery: bluetooth, nfc, wifi, wwan.
|
|
# Default: <none>
|
|
|
|
#DEVICES_TO_DISABLE_ON_BAT="bluetooth nfc wifi wwan"
|
|
|
|
# Radio devices to disable on battery when not in use (not connected):
|
|
# bluetooth, nfc, wifi, wwan.
|
|
# Default: <none>
|
|
|
|
#DEVICES_TO_DISABLE_ON_BAT_NOT_IN_USE="bluetooth nfc wifi wwan"
|
|
|
|
# Battery Care -- Charge thresholds
|
|
# Charging starts when the charge level is below the START_CHARGE_THRESH value
|
|
# when the charger is connected. It stops when the STOP_CHARGE_THRESH value is
|
|
# reached.
|
|
# Required hardware: Lenovo ThinkPads and select other laptop brands are driven
|
|
# via specific plugins, the actual support status is shown by tlp-stat -b.
|
|
# For more explanations and vendor specific details refer to
|
|
# https://linrunner.de/tlp/settings/battery.html
|
|
# Notes:
|
|
# - ThinkPads may require external kernel module(s), refer to the output of
|
|
# tlp-stat -b
|
|
# - Vendor specific parameter value ranges are shown by tlp-stat -b
|
|
# - If your hardware supports a start *and* a stop threshold, you must
|
|
# specify both, otherwise TLP will refuse to apply the single threshold
|
|
# - If your hardware supports only a stop threshold, set the start value to 0
|
|
|
|
# BAT0: Primary / Main / Internal battery (values in %)
|
|
# Note: also use for batteries BATC, BATT and CMB0
|
|
START_CHARGE_THRESH_BAT0=50
|
|
STOP_CHARGE_THRESH_BAT0=1
|
|
|
|
# BAT1: Secondary / Ultrabay / Slice / Replaceable battery (values in %)
|
|
# Note: primary on some laptops
|
|
# Default: <none>
|
|
|
|
#START_CHARGE_THRESH_BAT1=75
|
|
#STOP_CHARGE_THRESH_BAT1=80
|
|
|
|
# Restore charge thresholds when AC is unplugged: 0=disable, 1=enable.
|
|
RESTORE_THRESHOLDS_ON_BAT="1"
|
|
|
|
# Control battery care drivers: 0=disable, 1=enable.
|
|
NATACPI_ENABLE=1
|
|
TPACPI_ENABLE=1
|
|
TPSMAPI_ENABLE=1
|
|
|
|
# ------------------------------------------------------------------------------
|
|
# tlp-rdw - Parameters for the radio device wizard
|
|
|
|
# Possible devices: bluetooth, wifi, wwan.
|
|
# Separate multiple radio devices with spaces.
|
|
# Default: <none> (for all parameters below)
|
|
|
|
# Radio devices to disable on connect.
|
|
|
|
#DEVICES_TO_DISABLE_ON_LAN_CONNECT="wifi wwan"
|
|
#DEVICES_TO_DISABLE_ON_WIFI_CONNECT="wwan"
|
|
#DEVICES_TO_DISABLE_ON_WWAN_CONNECT="wifi"
|
|
|
|
# Radio devices to enable on disconnect.
|
|
|
|
#DEVICES_TO_ENABLE_ON_LAN_DISCONNECT="wifi wwan"
|
|
#DEVICES_TO_ENABLE_ON_WIFI_DISCONNECT=""
|
|
#DEVICES_TO_ENABLE_ON_WWAN_DISCONNECT=""
|
|
|
|
# Radio devices to enable/disable when docked.
|
|
|
|
#DEVICES_TO_ENABLE_ON_DOCK=""
|
|
#DEVICES_TO_DISABLE_ON_DOCK=""
|
|
|
|
# Radio devices to enable/disable when undocked.
|
|
|
|
#DEVICES_TO_ENABLE_ON_UNDOCK="wifi"
|
|
#DEVICES_TO_DISABLE_ON_UNDOCK=""
|